Can You Burn Off a Wart with a Soldering Iron?

This site contains affiliate links to products. We may receive a commission for purchases made through these links.

A wart is a small and grainy skin growth which often occurs on fingers or hands. Usually, warts are rough when touched and tend to feature a pattern of small dots commonly referred to as seeds.

These are small blood vessels that have clotted. The main cause of warts is a virus and is often transmitted through touch. This condition is common among children and young adults due to their weak immune system.

The best part is that warts often disappear on their own; this means that you don’t have to undergo any medical treatment. However, most individuals prefer removing them since they find it being embarrassing or bothersome. Several home treatment procedures are considered safe and very effective in removing warts.

However, there has been a recent trend where individuals use soldering iron to get rid of a wart. In this article, we shall be answering the question; can you burn off a wart with a soldering iron?

Burning Off The Wart Using Soldering Iron

AdobeStock 300011598 1

First and foremost, you should note that all medical hacks are not ideal for individuals with a weak stomach; therefore, you need to reconsider that before going through this article. Burning off the wart with a soldering iron has been proved to be effective by several individuals. This do-it-yourself health hack can be relatively painful.

You will need to use a good soldering iron tool and be prepared to endure the pain that comes with it. You don’t have to be scared since cauterization is a known and documented medical procedure. As an individual with a stomach that will withstand this procedure, then we highly recommend it since it has been proved to be significant compared to other wart removal procedures.

If you have a recurring wart on your hand or finger and you could not get rid of it irrespective of all methods you use, soldering iron might be the solution to your problem. Before you start getting rid of the wart with a soldering iron, you will need to rub your affected hand or finger with alcohol.

Once that is done, you can start applying the soldering iron for about two to three minutes. This technique will end up causing blisters around the sensitive skin next to the wart. Usually, this is due to the heat radiated by the soldering iron. You will need to hold the soldering iron at the right angle as you move it around the affected area.

Afterwards, it is all about playing the waiting game as you observe how the wart is as the days progress. Usually, on the second day, things might not look good since you will develop swollen blisters which are often not a great looking thing.

However, it would be best if you didn’t worry since the procedure is safe. It would be best if you played the waiting game. By the end of fourteen days, several parts of your skin will have dried and are ready to fall off. You can use a diagonal cutter to cut off the skin present on the dead wart. Once that is done, you will be on your way to full recovery.

After forty days, the affected finger or hand will be fully recovered, and you will be back to normal. This procedure works every time when done correctly. As an individual with courage, you can consider this procedure if you have a stubborn wart.

However, when soldering your wart, you might consider using aluminium foil around the affected finger or hand. While doing so, you should leave a small hole within the wart area for you to work on it. By doing so, you will be able to protect the surrounding area from a secondary burn that often results due to radiated heat from the soldering iron.

Other Wart Removing Methods

If you don’t have what it takes to use a soldering iron in removing a wart, you don’t have to worry since there are several other effective methods you might consider. Some of the effective ways include;

Salicylic acid

This is a peeling medicine, and it is a nonprescription wart removing product. As an individual suffering from common warts, you should consider looking for a 15% patch or 17% salicylic acid solution. Unlike soldering, this product will require daily use.

To achieve a significant result, you will need to soak your wart in warm water for approximately 10 to 20 minutes. Once that is done, you can apply the medication. It would be best if you considered filing away any available dead skin using a pumice stone or disposable emery board between treatments.


This is the opposite of cauterization. When freezing a wart, you will need to use a nitrogen product that is present in a nonprescription spray or liquid. However, the FDA cautions some warts removers are highly flammable, and they should not be used near a heat source, fire, lit cigarettes and flame.

Duct tape

When using duct tape, you will need to cover the wart affected area with silver duct tape for approximately six days. Once the six days are over, you will need to soak it in water and then remove the dead tissue gently using a disposable emery board or pumice stone.

You will then leave the wart exposed for approximately 12 hours. Afterwards, you will repeat the whole process until the wart disappears.

Final Verdict

Most doctors tend to use cauterization as a medical procedure for removing a wart. In addition to burning the wart, doctors will cut it or remove it using a laser. These treatment procedures are highly effective; however, it might leave a scar.

Soldering iron is said to feature the same medical procedure of cauterization. This means that the procedure is not only effective but also safe for use.

As a do-it-yourself enthusiast with a stomach for this procedure, you might consider doing it and get rid of some of the most stubborn warts with the utmost ease.

As we conclude this article, you should always remember that this procedure is relatively painful and is not best for faint-hearted individuals.

About The Author